Xantrex-technology Automatic Generator Instrukcja Użytkownika Strona 72
- Strona / 124
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuration
3–24 975-0082-01-01
Outcomes Selecting On enables the Start on Inverter Load Current (“Start Load”)
and Stop on Inverter Load Current (“Stop Load”) functionality. If the
Auto Gen Start is in Automatic mode and “Enable Load” is set to On, the
Auto Gen Start stops and starts the generator according to the values you
have set for “Start Load” and “Stop Load”.
Selecting Off disables the Start on Inverter Load Current and Stop on
Inverter Load Current functionality. When “Enable Load” is set to Off,
the Auto Gen Start ignores the values you have set for “Start Load” and
“Stop Load”.
Start Load
Full name Start on Inverter Load Current
Purpose “Start Load” is a changeable setting for enabling the generator to start at a
specified AC load on the inverter. The generator will assist the inverter
with powering the AC load.
This setting requires you to set a value for “Stop Load” also.
When to use You should change this setting if you have certain “peak” times of power
usage, or have power demands that consistently exceed the output of your
inverter.
If “Enable Load” is set to On, the generator will start in response to the
“Start Load” setting unless the Auto Gen Start is in a Quiet Time period.
Whenever the generator starts automatically in response to inverter load
current, the Auto Gen Start will stop the generator once the load on the
inverter reaches the Stop on Inverter Load Current value.
You can monitor the inverter load current on the System screen.
Outcomes If you set “Start Load” too high, the Auto Gen Start may not start the
generator in time to recharge the batteries before the batteries are drained
by the AC load. In addition, if “Start Load” is set too high, the inverter
may shut down due to an overload condition.
If you set “Start Load” too low, the Auto Gen Start may start the generator
too frequently, wasting fuel in the process.
Values Default
10.0A to 33.0A (increments of 1A) 10.0A
- Automatic 1
- Generator Start 1
- Automatic Generator Start 3
- About This Guide 5
- Organization 6
- Conventions Used 7
- Abbreviations and Acronyms 7
- Related Information 7
- Important Safety Instructions 9
- Explosive Gas Precautions 10
- FCC Information to the User 10
- Contents 11
- Configuration 12
- Operation 13
- Introduction 15
- 1–2 975-0082-01-01 16
- Features 17
- System Requirements 18
- Front and Bottom Panel 19
- Bottom panel 20
- CAUTION: Equipment Damage 20
- Xanbus System Components 21
- Installation 23
- Preparing an Installation 24
- Choosing a location 25
- Routing the connections 25
- WARNING: Explosion hazard 25
- Installing the Auto Gen Start 26
- Mounting the unit 27
- WARNING: Shock hazard 27
- 975-0082-01-01 2–7 29
- 18 AWG 16 AWG 29
- Table 2-1 30
- Contact numbers and functions 30
- Connecting the generator 31
- AGS wiring harness 33
- Generator wires 33
- Important:: 46
- 975-0082-01-01 2–25 47
- Verifying power is available 48
- CAUTION: 48
- Equipment damage 48
- 3–2 975-0082-01-01 50
- Changing Auto Gen Start 51
- [ManualOff] 52
- The Auto Gen Start Menu 53
- Figure 3-5 54
- Auto Gen Start menu contents 54
- The Auto Gen Start basic menu 55
- Gen Status 56
- Gen Trigger 56
- AGS Mode 57
- Important: 58
- QT Enable 59
- QT Begin 59
- 3–12 975-0082-01-01 60
- Start SOC 61
- Start DCV 62
- Enable Temp1 63
- Enable Temp2 64
- Gen Type 64
- Clear Faults 65
- Auto Gen Start advanced menu 66
- AGS Triggers menu 67
- StartV:30sec 68
- StartV:15min 68
- StartV:2hr 69
- StartV:24hr 70
- StopBattV 70
- Enable Load 71
- Start Load 72
- Stop Load 73
- Stop Absorb 73
- Stop Float 74
- 975-0082-01-01 3–27 75
- Generator Configuration menu 76
- Exercise Per 77
- Max Run Time 77
- Exercise Dur 78
- Exercise Time 79
- Run Hold Time 80
- Crank Time 80
- Crank Retry Time 81
- Preheat Time 81
- Start Tries 82
- AGS: Device Info menu 83
- User Settings 84
- 4–2 975-0082-01-01 86
- Setting Quiet Time 87
- Setting the end of Quiet Time 88
- Viewing the Advanced Menu 89
- Changing System Modes 90
- Operating mode 91
- Power Save mode 91
- Safe mode 91
- Hibernate mode 92
- Troubleshooting 93
- Faults and Warnings 94
- Warning Messages 95
- Table 5-1 96
- Fault Messages 97
- Table 5-2 98
- Auto Gen Start fault messages 98
- Specifications 99
- Electrical Specifications 100
- Mechanical Specifications 100
- Environmental Specifications 101
- Regulatory Compliance 101
- Start Requirements 103
- Generator Auto 103
- Recommended Features 104
- Generator Starting Types 104
- Two wire 105
- Three-Wire Onan 105
- Three-Wire Automotive 106
- Relay Timing 107
- C–2 975-0082-01-01 108
- MomentaryRun Mode 109
- GlowStop Mode 110
- StartStop Mode 110
- Shutdown 111
- Warranty 113
- Disclaimer 115
- Return Procedure 116
- Out of Warranty Service 116
- Information About Your System 117
- Printed in China 124
Powiązane produkty i podręczniki dla Generatory Xantrex-technology Automatic Generator
(80 strony)Huawei HUAWEI Y5 Pro manuals
Owner’s manuals and user’s guides for Smartphones Huawei HUAWEI Y5 Pro.
We providing 1 pdf manuals Huawei HUAWEI Y5 Pro for download free by document types: User Manual
Komentarze do niniejszej Instrukcji